Our extensive Amana Air Conditioner Repair Guide will help you troubleshoot many issues related to your Amana air conditioner, from replacing your air filter to common problems!
Please note, the following is for informational purposes only. Any servicing you attempt is at your own risk.
Table of contents
Amana, At a Glance
Born in 1934, Amana has been designing and manufacturing reliable heating and cooling products for almost 100 years. The brand has been repeatedly recognized as the producer of some of the most energy-efficient systems on the market, thanks to their exceedingly impressive ratings and ENERGY STAR® certifications.
Additionally, Amana air conditioning products are backed by the brand’s extensive warranty coverage to ensure that Canadian homeowners can rest easy should any issues arise.
Remembering to replace your Amana unit’s air filter regularly will significantly lengthen the air conditioner’s life. Additionally, frequently vacuuming the registers and keeping the area surrounding your air conditioner free of debris will contribute positively to your system’s performance. These simple practices will guarantee efficient and long-lasting cooling comfort.
How to Replace Your Amana Air Filter
Follow these simple steps to replace your Amana air filter:
- Turn off the system’s power
- Open the panel to gain access
- Find your air conditioner’s filter. Usually, these are located near the return air duct
- Remove the dirty air filter
- If it’s reusable, clean the filter, or grab a new one if you’re using disposable filters
- Reinsert the cleaned or new air filter
- Replace the access panel and turn the power back on
What’s Wrong With Your Amana Air Conditioner?
Remember to turn your a/c completely off before opening it up to look around or attempt any fix.
Is air not coming out of the floor and ceiling registers?
If there isn’t any air movement, check to see if the outside unit fan is operating. If it isn’t, you’ll have to see if the air conditioner’s breaker is defective.
Is the outside unit only blowing hot air?
If you notice that the compressor starts operating, but the fan doesn’t, the condenser fan might be defective. However, if the condenser fan works but the compressor doesn’t, the unit could either be low on refrigerant or have a defective compressor.
If the blower motor isn’t running, but the fan outside operates properly, then you should check to see if the blower motor is defective. Alternatively, there could be an issue with the control board or run capacitor.
Is your air conditioner providing insufficient cooling comfort?
If the compressor and condenser fan both seem functional, but your home doesn’t feel as comfortable as it should, then your system might require some maintenance. Measure your system’s temperature drop; if it reads significantly lower than it should, your air conditioner refrigerant charge may be defective.
On the other hand, if the reading is too high, then you should examine the blower motor, air filter, or evaporator coil – any of these components might be dirty or faulty.
Amana Air Conditioner Error Codes
Note that these error codes may or may not be accurate or apply to your system. Each manufacturer has a range of different sensor and error codes used for different model lines and these may differ from one model series, production run, region, and may have been updated at any time. This not a comprehensive list and these are for informational purposes only. Any use of them is at your own risk.
Fault Codes
Fault Code | PCB LED Display | Thermostat Fault | |
---|---|---|---|
12 | E12 | OD CTRL FAIL1 | Indicates a general memory error. |
13 | E13 | HI PRESSURE C (C = CRITICAL) | This error indicates the equipment is experiencing frequent high pressure faults. |
14 | E14 | HI PRESSURE M (M = MINOR) | This error indicates the equipment is experiencing frequent high pressure faults. Control has determined continued operation is acceptable. This indicates they may be a problem with the equipment. |
15 | E15 | LOW PRESSURE C | This error indicates the equipment is experiencing frequent low pressure faults. |
16 | E16 | LOW PRESSURE M | This error indicates the equipment is experiencing frequent low pressure faults. Control has determined continued operation is acceptable. This indicates they may be a problem with the equipment. |
17 | E17 | COMPRESSOR FAIL | This error indicates the equipment is experiencing frequent compressor faults. |
18 | E18 | OD CTRL FAIL2 | Indicates the control board may need to be replaced |
19 | E19 | PCB OR FAN FAIL | This error indicates the equipment is experiencing frequent outdoor control board and/or motor faults. |
21 | E21 | EEV CTRL FAIL | This error indicates the equipment is experiencing frequent low discharge superheat faults. |
22 | E22 | HI DISCH TEMP | This error indicates the equipment is experiencing frequent high discharge temperature faults. Discharge thermistor is not put on correct position. |
23 | E23 | DISCH TEMP FAIL | The control has detected that the Discharge Temperature Sensor is out of range. |
24 | E24 | HPS OPEN | The high pressure switch is open. |
25 | E25 | AIR SENSOR FLT | The outdoor air temperature sensor is open or shorted. |
26 | E26 | PRESSURE SENSOR | The control determines that the pressure sensor is not reacting properly. |
28 | E28 | COIL TEMP FAIL2 | The control has detected that the Outdoor Coil Temperature Sensor is out of range. |
29 | E29 | LIQ TEMP FAIL | The control has detected that the Liquid Temperature Sensor is out of range. |
30 | E30 | OD CTRL FAIL3 | Indicates the control board may need to be replaced. |
31 | E31 | HI LEAK CURRENT | The control has detected high leakage current (high voltege). |
32 | E32 | HI TEMP CTRL1 | This error indicates the equipment is experiencing high temperature faults on the outdoor control board |
33 | E33 | HI TEMP CTRL 2 | This error indicates the equipment is experiencing high temperature faults on the outdoor control board. Control has determined continued operation is acceptable. This indicates they may be a problem with the equipment. |
34 | E34 | CURRENT SPIKE | Board detected a high current condition. This indicates the potential for a short circuit. |
35 | E35 | HIGH CURRENT | Board detected a high current condition |
36 | E36 | STARTUP ERROR | The control encountered an abnormal condition during the startup procedure |
37 | E37 | OD CTRL FAIL 4 | Indicates the control board may need to be replaced. |
38 | E38 | COMP VOLTAGE | The control has detected a voltage related issue with the compressor |
39 | E39 | OD CTRL FAIL 5 | Indicates the control board may need to be replaced. |
40 | E40 | COMP MISMATCH | Control determines that its compressor requirement is different than the compressor capability |
41 | E41 | LOW REFRIGERANT | The control has detected a low refrigerant condition |
42 | E42 | LOW LINE VOLT | Control detects a low power supply voltage condition |
43 | E43 | HIGH LINE VOLT | Control detects a high power supply voltage condition. |
44 | E44 | OP TEMP RANGE | The control detects the outdoor temperature outside recommended operational range. Unit may continue to operate normally. |
45 | E45 | NO COOLING TEST | The control is unable to start the Cooling mode test because indoor heat has been turned on by thermostat. Please set thermostat to off position. |
47 | E47 | NO SYS VER TEST | The control is unable to start the System Verification test because indoor heat has been turned on by thermostat. Please set thermostat to off position. |
48 | E48 | NO PUMP DOWN | The control is unable to enter the Pump Down Mode because indoor heat has been turned on by thermostat. Please set thermostat to off position |
49 | E49 | NO CHARGE MODE | The control is unable to enter Charging Mode because indoor heat has been turned on by thermostat. Please set thermostat to off position |
50 | E50 | LINE VOLT CTRL | This indicates there is a voltage issue on the control board. See service manual for troubleshooting information |
51 | E51 | OD COMM ERROR | This indicates potential communication issues have been detected by the outdoor control board |
52 | E52 | COMP FAIL MINOR | This error indicates the equipment is experiencing frequent compressor faults. Control has determined continued operation is acceptable. This indicates they may be a problem with the equipment. |
53 | E53 | PCB PR FAN MIN | This error indicates the equipment is experiencing frequent outdoor control board and/or motor faults. Control has determined continued operation is acceptable. This indicates there may be a problem with the equipment. |
54 | E54 | EEV MINOR | This error indicates the equipment is experiencing frequent low discharge superheat faults. Control has determined continued operation is acceptable. This indicates they may be a problem with the equipment. |
55 | E55 | HI DIS TEMP MIN | This error indicates the equipment is experiencing frequent high discharge temperature faults. Control has determined continued operation is acceptable. This indicates they may be a problem with the equipment |
57 | E57 | CL LOOP SWEAT | This indicates the control is sensing sweating on the cooling loop. |
B0 | Eb0 | NO ID AIRFLOW | The estimated airflow from indoor subsystem is near to 0 CFM. |
B9 | Eb9 | LOW ID AIRFLOW | Estimated airflow from motor is lower than the airflow requirement. |
D0 | Ed0 | NO NET DATA | Control board does not have the necessary data for it to properly perform its functions |
D1 | Ed1 | INVALID DATA | Control board does not the appropriate data needed to properly perform its functions. |
D2 | Ed2 | INVALID SYSTEM | The airflow requirement is greater than the airflow capability of the indoor subsystem. |
D3 | Ed3 | INVALID CONFIG | There is a mismatch between the shared data and the control physical hardware |
D4 | Ed4 | INVALID MC DATA | The memory card data has been rejected. |
11 | E11 | RUN SYS TEST | This test is required at startup. Installer should navigate to the ComforrtNet User Menu, choose Air Conditioner, then EQUIP TEST and SYSYTEM TEST. Selecting ON will run the required test. Display will clear once testing is complete. |
LED Codes
Status LED | Status LED Description |
---|---|
Green "POWER" | Module has power |
Red "TRIP" | Thermostat demand signal Y1 is present, but thecompressor is not running |
Yellow "ALERT"Flash Code 1 | Long Run Time Compressor is running extremely long run cycles |
Yellow "ALERT" Flash Code 2 | System Pressure Trip Discharge or suction pressure out of limits or compressor overloaded |
Yellow "ALERT" Flash Code 3 | Short Cycling Compressor is running only briefly |
Yellow "ALERT" Flash Code 4 | Locked Rotor |
Yellow "ALERT" Flash Code 5 | Open Circuit |
Yellow "ALERT" Flash Code 6 | Open Start Circuit Current only in run circuit |
Yellow "ALERT" Flash Code 7 | Open Run Circuit Current only in start circuit |
Yellow "ALERT" Flash Code 8 | Welded Contactor Compressor always runs |
Yellow "ALERT" Flash Code 9 | Low VoltageControl circuit < 17VAC |
When to Get a Technician for Amana Air Conditioner Repairs
When your Amana air conditioner begins to experience performance issues, it can be challenging to know whether or not you need to contact a trained HVAC technician. It’s one thing to be able to diagnose a potential issue. It’s another thing entirely to go about performing the repair. In these types of situations, it’s not a bad call to bring in a professional to take a look. Although it might cost you some money, it’ll save you plenty long-term if the fix is complex.
Who to Call For Amana Air Conditioner Repairs
Should you be looking for trustworthy heating and cooling professional, online consumer reviews are a great place to begin your search. They can detail the types of services offered by businesses as well as their potential prices while giving you a rough assessment of the quality.
It’s important to remember, however, that consumer reviews can’t be trusted absolutely. This is due to the biased nature of online reviews, don’t invest thousands of dollars solely based on the words of an anonymous poster.
Our independent certification program can help you connect with dependable local HVAC professionals. We compile a list of approved heating and cooling companies that fit a number of criteria, such as proof of insurance and successful track record. This way, you can be assured knowing that you’ve made an informed decision.
Amana’s Warranty Coverage
Depending on what tier of air conditioning system you purchased, Amana offers Canadian homeowners a range of coverage options to best protect their investment.
- Premium- and mid-range air conditioners, such as the AVXC20 and ASX16, are covered by a limited lifetime unit replacement warranty as well as a limited 10-year parts protection warranty.
- Budget-friendly options, like the ASX14, receive Amana’s base limited 10-year parts protection warranty.
Protect your Amana air conditioner: Register and access your Amana A/C warranty here